18.5" x 75.5" Short Board 18.5" x 75.5" Short Board
Online
$905.88 for EA
Retail $1518.00
Mfr PN: 365079
Stock: 3
Reinventing what surfing could be, this western red cedar surf board is a true gem for even the most experienced wave rider. Handcrafted and then encapsulated in fiberglass epoxy it can certainly stand up to the toughest of watery terrains. The design is phenomenal, featuring three smooth and rich looking fins all about 8 in length. With a 2 thickness, this solid piece will keep you surfing for hours. Engineered for ultimate performance, the board is perhaps most notable for its deep toned beauty. Craftsmanship galore represents the best of what this board has to offer. The thickness of the board is about 2" and it has 3 fins. Each fin is about 8" in length. This surfboard weight at 12.65 lbs.
Online
$905.88 for EA
Retail $1518.00
Mfr PN: 365079
Stock: 3

24" x 109" Long Board 24" x 109" Long Board
Online
$1418.48 for EA
Retail $2059.00
Mfr PN: 365078
Stock: 1
With ultra stylish fins and a sleek, glossy exterior, this surfboard will be difficult to miss when out riding waves or even at rest on the beach. Made of high quality Canadian western red cedar and then finished in a durable fiberglass epoxy, this handmade board will not only provide you the ride of a lifetime, but put all other boards out there to shame. Youve never experienced surfing like this. At approximately 2 thick, weighing 22 lbs, it will be easy to jump in your vehicle, load it up and take off for some fun in the sun!
Online
$1418.48 for EA
Retail $2059.00
Mfr PN: 365078
Stock: 1

ANDERSEN 12 ST FS Self-Tailing Manual Single Speed Winch - Full Stainless ANDERSEN 12 ST FS Self-Tailing Manual Single Speed Winch - Full Stainless
Online
$508.98 for Each
Mfr PN: RA2012010000
Stock: 2

12 ST FS Self-Tailing Manual Single Speed Winch - Full Stainless

Power Rib™

ANDERSEN Winches feature the Power Rib™. Unlike other winches with abrasive drum surfaces, ANDERSEN winch drums have vertical ribs running up the surface. This combined with the smooth polished stainless steel gives a maximum grip and minimum wear on ropes, reducing the replacements costs of sheets and halyards. What’s more, the Power Rib principle simply makes sailing more pleasurable. Fewer turns on the winch make tacking easier. Sheets can be gently eased out without harsh snatching and the risks of overrides and jammed sheets are significantly reduced. The grip provided by the ribs will remain the same year after year, unlike many other winches with an abrasive or sandpaper-like surface. Such surfaces have a tendency to wear down both ropes and themselves.

Power Ratio

Power Ratio is the mechanical advantage of the winch and is calculated as follows:

length of handle x gear ratio 
          radius of drum

The pull of the winch is based on the Power Ratio and not just on the physical size of the winch or the diameter of the drum. The Power Ratio is used to determine the load the winch may handle as follows: pull of handle (kg x Power Ratio = pull of winch (kg).

This means that by applying a load of 10kg, using a 10" standard handle, on a Power Ratio 40:1 winch, the winch can pull 400kg, assuming that the winch is 100% efficient. This is not possible in practice as the efficiency is reduced by internal mechanical friction losses.

Specifications:

  • Drum Ø D: 2-3/4"
  • Base Ø B: 4-1/2"
  • Height H: 5"
  • Line Entry L: 1-3/4"
  • Line Size: 5/16-9/16"
  • Weight: 5.7lb
  • Gear ratio 1st speed: 1.3 : 1
  • Power ratio 1st speed: 9.5 :1
Online
$508.98 for Each
Mfr PN: RA2012010000
Stock: 2

ANDERSEN 18 ST FS Self-Tailing Manual Single Speed Winch - Full Stainless ANDERSEN 18 ST FS Self-Tailing Manual Single Speed Winch - Full Stainless
Online
$617.52 for Each
Mfr PN: RA2018010000
Stock: 2

18 ST FS Self-Tailing Manual Single Speed Winch - Full Stainless

Power Rib™

ANDERSEN Winches feature the Power Rib™. Unlike other winches with abrasive drum surfaces, ANDERSEN winch drums have vertical ribs running up the surface. This combined with the smooth polished stainless steel gives a maximum grip and minimum wear on ropes, reducing the replacements costs of sheets and halyards. What’s more, the Power Rib principle simply makes sailing more pleasurable. Fewer turns on the winch make tacking easier. Sheets can be gently eased out without harsh snatching and the risks of overrides and jammed sheets are significantly reduced. The grip provided by the ribs will remain the same year after year, unlike many other winches with an abrasive or sandpaper-like surface. Such surfaces have a tendency to wear down both ropes and themselves.

Power Ratio

Power Ratio is the mechanical advantage of the winch and is calculated as follows:

length of handle x gear ratio 
          radius of drum

The pull of the winch is based on the Power Ratio and not just on the physical size of the winch or the diameter of the drum. The Power Ratio is used to determine the load the winch may handle as follows: pull of handle (kg x Power Ratio = pull of winch (kg).

This means that by applying a load of 10kg, using a 10" standard handle, on a Power Ratio 40:1 winch, the winch can pull 400kg, assuming that the winch is 100% efficient. This is not possible in practice as the efficiency is reduced by internal mechanical friction losses.

Specifications:

  • Drum Ø D: 2-3/4"
  • Base Ø B: 4-3/4"
  • Height H: 5-1/4"
  • Line Entry L: 1-15/16"
  • Line Size: 1/8-11/16"
  • Weight: 7.0lb
  • Gear ratio 1st speed: 2.6 : 1
  • Power ratio 1st speed: 18.8 :1
Online
$617.52 for Each
Mfr PN: RA2018010000
Stock: 2

ANDERSEN 28 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel ANDERSEN 28 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel
Online
$888.84 for Each
Mfr PN: RA2028010000
Stock: 3

28 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel


If you take pride in having your yacht look its best, ANDERSEN's Full Stainless Self-Tailing Winch creates the dock-stopping appeal you desire. It combines all the convenience and power of ANDERSEN's self-tailing winch with a stunning all stainless steel look.

From top to bottom the drive shaft stripper arm, self-tailing jaws, drum and upper & lower trim rings are manufactured in highest quality and beautifully polished grade 316 stainless steel. The dramatic result is a highly reflective winch that becomes a highlight of the boat and a true reflection of your yachting pride. We like to say, “Full Stainless – Beyond Good Looks.”

As with all ANDERSEN Winches™, our Full Stainless Self-Tailing winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Materials

Andersen winch drums are produced from grade 316L stainless steel, cold formed in stages during manufacture to further increase strength and hardness as it takes its final form. The resulting construction is lightweight, yet stiff and unyielding. 

Drive shafts are in grade 329 duplex stainless steel. Pawls are cut from a cold pressed profile in grade 316 stainless steel and are virtually unbreakable. 

The upper center stems are manufactured from aluminum bronze for ultimate durability. The combination of materials and design contribute to a lightweight, rigid final assembly that enhances. the mechanical efficiency of the winch. Andersen winces are of similar weight to winches with aluminum drums, but are far more durable. 

Power Rib™

ANDERSEN Winches© feature the Power Rib™. Unlike other winches with abrasive drum surfaces, ANDERSEN winch drums have vertical ribs running up the surface. This combined with the smooth polished stainless steel gives a maximum grip and minimum wear on ropes, reducing the replacements costs of sheets and halyards. What's more, the Power Rib principle simply makes sailing more pleasurable. Fewer turns on the winch make tacking easier. Sheets can be gently eased out without harsh snatching and the risks of overrides and jammed sheets are significantly reduced. The grip provided by the ribs will remain the same year after year, unlike many other winches with an abrasive or sandpaper-like surface. Such surfaces have a tendency to wear down both ropes and themselves.

Power Ratio

Power Ratio is the mechanical advantage of the winch and is calculated as follows:

length of handle x gear ratio

        radius of drum

The pull of the winch is based on the Power Ratio and not just on the physical size of the winch or the diameter of the drum. The Power Ratio is used to determine the load the winch may handle as follows:pull of handle (kg x Power Ratio = pull of winch (kg).

This means that by applying a load of 10kg, using a 10" standard handle, on a Power Ratio 40:1 winch, the winch can pull 400kg, assuming that the winch is 100% efficient. This is not possible in practice as the efficiency is reduced by internal mechanical friction losses.

Features

Anderson winch drums incorporate the distinctive Power Rib which ensures a controlled grip on the line at all times, whether trimming or easing. The highly polished stainless steel surface minimizes vertical friction and allows the loaded rope turns to slide easily upward as the drum rotates, without the shuddering and excessive rope wear seen on winches that rely on a rough surface finish for grip. 

Stainless steel roller bearings and ball bearings carry the

Online
$888.84 for Each
Mfr PN: RA2028010000
Stock: 3

ANDERSEN 28ST Compact Below Deck Electric FS Winch Variable Speed - 12V ANDERSEN 28ST Compact Below Deck Electric FS Winch Variable Speed - 12V
Online
$4845.68 for Each
Retail $5094.90
Mfr PN: RA2028014100
Stock: 1

28ST Compact Below Deck Electric Full Stainless Winch Variable Speed - 12V

Andersen Compact Motor™ electric winches allow you to hoist and trim sails at the push of a button regardless of physical strength, so any crew member can easily and safely trim sails and control lines.

Ease of installation
The Andersen Compact Motor™ electric winch is available in two formats for either Above Deck or Below Deck motor placement. Motor gearbox and controller are integrated into one compact unit with no extra control box necessary. Simplified electrical installation requires just the connection of positive and negative power cables to the motor terminals and the connection of the push button using the included output cable.

Efficient, variable speed
The Andersen Compact Motor™ is a brushless DC motor carefully matched to a low profile planetary gearbox which requires less space for installation, and draws considerably less current than traditional motor/gearbox configurations. Available in 12 volt and 24 volt models, Compact Motor™ electric winches operate at variable speed in proportion to the pressure applied to the push button, for smooth and quiet operation.

Illuminated "intelligent" push button
Compact Motor™ winches are supplied with a push button with integrated LED which illuminates when power to the winch system is on. The push button incorporates a hinged safety cover to prevent inadvertent winch operation and is water resistant rated to IP67. The push button also acts with the controller to flash status codes that assist with trouble shooting in the event of overload or where other system protection intervention occurs. A cable for connection of the push button is included for convenient installation.

Built-in protection
- Integrated overload protection - The controller is pre-set to stop the winch if the maximum pull load is exceeded. Operation can resume within a few seconds when the load returns below the limit.
- Thermal overload protection - The motor is fitted with a thermal cutout that disables the motor in case of overheating; it automatically resets after the temperature returns to normal.

As with all ANDERSEN Winches™, our Compact Motor™ Electric Winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Specifications

  • Drum: 2-3/4 in. (70 mm)
  • Base: 4-15/16 in. (125 mm)
  • Height: 6-3/16 in. (157 mm)
  • Line Entry: 2-7/8 in. (73 mm)
  • Line Size: 5/16-9/16 in. (8-14 mm)
  • Weight: 37.5 lbs. (17 kg)
  • Max Deck Thickness: 2-1/8 in. (54 mm)
  • Motor Depth: 7-1/16 in. (180 mm)
  • Motor: 7-11/16 in. (195 mm)
Online
$4845.68 for Each
Retail $5094.90
Mfr PN: RA2028014100
Stock: 1

ANDERSEN 34 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel ANDERSEN 34 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel
Online
$997.36 for Each
Mfr PN: RA2034010000
Stock: 3

34 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel


If you take pride in having your yacht look its best, ANDERSEN's Full Stainless Self-Tailing Winch creates the dock-stopping appeal you desire. It combines all the convenience and power of ANDERSEN's self-tailing winch with a stunning all stainless steel look.

From top to bottom the drive shaft stripper arm, self-tailing jaws, drum and upper & lower trim rings are manufactured in highest quality and beautifully polished grade 316 stainless steel. The dramatic result is a highly reflective winch that becomes a highlight of the boat and a true reflection of your yachting pride. We like to say, “Full Stainless – Beyond Good Looks.”

As with all ANDERSEN Winches™, our Full Stainless Self-Tailing winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Materials

Andersen winch drums are produced from grade 316L stainless steel, cold formed in stages during manufacture to further increase strength and hardness as it takes its final form. The resulting construction is lightweight, yet stiff and unyielding. 

Drive shafts are in grade 329 duplex stainless steel. Pawls are cut from a cold pressed profile in grade 316 stainless steel and are virtually unbreakable. 

The upper center stems are manufactured from aluminum bronze for ultimate durability. The combination of materials and design contribute to a lightweight, rigid final assembly that enhances. the mechanical efficiency of the winch. Andersen winces are of similar weight to winches with aluminum drums, but are far more durable. 

Power Rib™

ANDERSEN Winches© feature the Power Rib™. Unlike other winches with abrasive drum surfaces, ANDERSEN winch drums have vertical ribs running up the surface. This combined with the smooth polished stainless steel gives a maximum grip and minimum wear on ropes, reducing the replacements costs of sheets and halyards. What's more, the Power Rib principle simply makes sailing more pleasurable. Fewer turns on the winch make tacking easier. Sheets can be gently eased out without harsh snatching and the risks of overrides and jammed sheets are significantly reduced. The grip provided by the ribs will remain the same year after year, unlike many other winches with an abrasive or sandpaper-like surface. Such surfaces have a tendency to wear down both ropes and themselves.

Power Ratio

Power Ratio is the mechanical advantage of the winch and is calculated as follows:

length of handle x gear ratio

        radius of drum

The pull of the winch is based on the Power Ratio and not just on the physical size of the winch or the diameter of the drum. The Power Ratio is used to determine the load the winch may handle as follows:pull of handle (kg x Power Ratio = pull of winch (kg).

This means that by applying a load of 10kg, using a 10" standard handle, on a Power Ratio 40:1 winch, the winch can pull 400kg, assuming that the winch is 100% efficient. This is not possible in practice as the efficiency is reduced by internal mechanical friction losses.

Features

Anderson winch drums incorporate the distinctive Power Rib which ensures a controlled grip on the line at all times, whether trimming or easing. The highly polished stainless steel surface minimizes vertical friction and allows the loaded rope turns to slide easily upward as the drum rotates, without the shuddering and excessive rope wear seen on winches that rely on a rough surface finish for grip. 

Stainless steel roller bearings and ball bearings carry the

Online
$997.36 for Each
Mfr PN: RA2034010000
Stock: 3

ANDERSEN 34ST Compact Below Deck Electric FS Winch Variable Speed - 12V ANDERSEN 34ST Compact Below Deck Electric FS Winch Variable Speed - 12V
Online
$4687.48 for Each
Retail $5247.90
Mfr PN: RA2034014100
Stock: 2

34ST Compact Below Deck Electric Full Stainless Winch Variable Speed - 12V

Andersen Compact Motor™ electric winches allow you to hoist and trim sails at the push of a button regardless of physical strength, so any crew member can easily and safely trim sails and control lines.

Ease of installation
The Andersen Compact Motor™ electric winch is available in two formats for either Above Deck or Below Deck motor placement. Motor gearbox and controller are integrated into one compact unit with no extra control box necessary. Simplified electrical installation requires just the connection of positive and negative power cables to the motor terminals and the connection of the push button using the included output cable.

Efficient, variable speed
The Andersen Compact Motor™ is a brushless DC motor carefully matched to a low profile planetary gearbox which requires less space for installation, and draws considerably less current than traditional motor/gearbox configurations. Available in 12 volt and 24 volt models, Compact Motor™ electric winches operate at variable speed in proportion to the pressure applied to the push button, for smooth and quiet operation.

Illuminated "intelligent" push button
Compact Motor™ winches are supplied with a push button with integrated LED which illuminates when power to the winch system is on. The push button incorporates a hinged safety cover to prevent inadvertent winch operation and is water resistant rated to IP67. The push button also acts with the controller to flash status codes that assist with trouble shooting in the event of overload or where other system protection intervention occurs. A cable for connection of the push button is included for convenient installation.

Built-in protection
- Integrated overload protection - The controller is pre-set to stop the winch if the maximum pull load is exceeded. Operation can resume within a few seconds when the load returns below the limit.
- Thermal overload protection - The motor is fitted with a thermal cutout that disables the motor in case of overheating; it automatically resets after the temperature returns to normal.

As with all ANDERSEN Winches™, our Compact Motor™ Electric Winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Specifications

  • Drum: 2-3/4 in. (70 mm)
  • Base: 4-15/16 in. (125 mm)
  • Height: 6-3/16 in. (157 mm)
  • Line Entry: 2-7/8 in. (73 mm)
  • Line Size: 5/16-9/16 in. (8-14 mm)
  • Weight: 37.5 lbs. (17 kg)
  • Max Deck Thickness: 2-1/8 in. (54 mm)
  • Motor Depth: 7-1/16 in. (180 mm)
  • Motor: 7-11/16 in. (195 mm)
Online
$4687.48 for Each
Retail $5247.90
Mfr PN: RA2034014100
Stock: 2

ANDERSEN 40 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel ANDERSEN 40 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel
Online
$1105.89 for Each
Mfr PN: RA2040010000
Stock: 2

40 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel

If you take pride in having your yacht look its best, ANDERSEN's Full Stainless Self-Tailing Winch creates the dock-stopping appeal you desire. It combines all the convenience and power of ANDERSEN's self-tailing winch with a stunning all stainless steel look.

From top to bottom the drive shaft stripper arm, self-tailing jaws, drum and upper & lower trim rings are manufactured in highest quality and beautifully polished grade 316 stainless steel. The dramatic result is a highly reflective winch that becomes a highlight of the boat and a true reflection of your yachting pride. We like to say, “Full Stainless – Beyond Good Looks.”

As with all ANDERSEN Winches™, our Full Stainless Self-Tailing winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Materials

Andersen winch drums are produced from grade 316L stainless steel, cold formed in stages during manufacture to further increase strength and hardness as it takes its final form. The resulting construction is lightweight, yet stiff and unyielding. 

Drive shafts are in grade 329 duplex stainless steel. Pawls are cut from a cold pressed profile in grade 316 stainless steel and are virtually unbreakable. 

The upper center stems are manufactured from aluminum bronze for ultimate durability. The combination of materials and design contribute to a lightweight, rigid final assembly that enhances. the mechanical efficiency of the winch. Andersen winces are of similar weight to winches with aluminum drums, but are far more durable. 

Power Rib™

ANDERSEN Winches© feature the Power Rib™. Unlike other winches with abrasive drum surfaces, ANDERSEN winch drums have vertical ribs running up the surface. This combined with the smooth polished stainless steel gives a maximum grip and minimum wear on ropes, reducing the replacements costs of sheets and halyards. What's more, the Power Rib principle simply makes sailing more pleasurable. Fewer turns on the winch make tacking easier. Sheets can be gently eased out without harsh snatching and the risks of overrides and jammed sheets are significantly reduced. The grip provided by the ribs will remain the same year after year, unlike many other winches with an abrasive or sandpaper-like surface. Such surfaces have a tendency to wear down both ropes and themselves.

Power Ratio

Power Ratio is the mechanical advantage of the winch and is calculated as follows:

length of handle x gear ratio

        radius of drum

The pull of the winch is based on the Power Ratio and not just on the physical size of the winch or the diameter of the drum. The Power Ratio is used to determine the load the winch may handle as follows:pull of handle (kg x Power Ratio = pull of winch (kg).

This means that by applying a load of 10kg, using a 10" standard handle, on a Power Ratio 40:1 winch, the winch can pull 400kg, assuming that the winch is 100% efficient. This is not possible in practice as the efficiency is reduced by internal mechanical friction losses.

Features

Anderson winch drums incorporate the distinctive Power Rib which ensures a controlled grip on the line at all times, whether trimming or easing. The highly polished stainless steel surface minimizes vertical friction and allows the loaded rope turns to slide easily upward as the drum rotates, without the shuddering and excessive rope wear seen on winches that rely on a rough surface finish for grip. 

Stainless steel roller bearings and ball bearings carry the highest drum loads to the ce

Online
$1105.89 for Each
Mfr PN: RA2040010000
Stock: 2

ANDERSEN 40ST Compact Below Deck Electric FS Winch Variable Speed - 12V ANDERSEN 40ST Compact Below Deck Electric FS Winch Variable Speed - 12V
Online
$4812.48 for Each
Retail $5400.90
Mfr PN: RA2040014100
Stock: 2

40ST Compact Below Deck Electric Full Stainless Winch Variable Speed - 12V

Andersen Compact Motor™ electric winches allow you to hoist and trim sails at the push of a button regardless of physical strength, so any crew member can easily and safely trim sails and control lines.

Ease of installation
The Andersen Compact Motor™ electric winch is available in two formats for either Above Deck or Below Deck motor placement. Motor gearbox and controller are integrated into one compact unit with no extra control box necessary. Simplified electrical installation requires just the connection of positive and negative power cables to the motor terminals and the connection of the push button using the included output cable.

Efficient, variable speed
The Andersen Compact Motor™ is a brushless DC motor carefully matched to a low profile planetary gearbox which requires less space for installation, and draws considerably less current than traditional motor/gearbox configurations. Available in 12 volt and 24 volt models, Compact Motor™ electric winches operate at variable speed in proportion to the pressure applied to the push button, for smooth and quiet operation.

Illuminated "intelligent" push button
Compact Motor™ winches are supplied with a push button with integrated LED which illuminates when power to the winch system is on. The push button incorporates a hinged safety cover to prevent inadvertent winch operation and is water resistant rated to IP67. The push button also acts with the controller to flash status codes that assist with trouble shooting in the event of overload or where other system protection intervention occurs. A cable for connection of the push button is included for convenient installation.

Built-in protection
- Integrated overload protection - The controller is pre-set to stop the winch if the maximum pull load is exceeded. Operation can resume within a few seconds when the load returns below the limit.
- Thermal overload protection - The motor is fitted with a thermal cutout that disables the motor in case of overheating; it automatically resets after the temperature returns to normal.

As with all ANDERSEN Winches™, our Compact Motor™ Electric Winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Specifications

  • Drum: 2-15/16 in. (75 mm)
  • Base: 6 in. (152 mm)
  • Height: 7-1/16 in. (180 mm)
  • Line Entry: 3-1/8 in. (79 mm)
  • Line Size: 5/16-9/16 in. (8-14 mm)
  • Weight: 40 lbs. (18 kg)
  • Max Deck Thickness: 2-1/8 in. (54 mm)
  • Motor Depth: 7-1/16 in. (180 mm)
  • Motor: 7-11/16 in. (195 mm)
Online
$4812.48 for Each
Retail $5400.90
Mfr PN: RA2040014100
Stock: 2

ANDERSEN 46 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel ANDERSEN 46 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel
Online
$1453.92 for Each
Mfr PN: RA2046010000
Stock: 2

40 ST FS - 2-Speed Self-Tailing Manual Winch - Full Stainless Steel

If you take pride in having your yacht look its best, ANDERSEN's Full Stainless Self-Tailing Winch creates the dock-stopping appeal you desire. It combines all the convenience and power of ANDERSEN's self-tailing winch with a stunning all stainless steel look.

From top to bottom the drive shaft stripper arm, self-tailing jaws, drum and upper & lower trim rings are manufactured in highest quality and beautifully polished grade 316 stainless steel. The dramatic result is a highly reflective winch that becomes a highlight of the boat and a true reflection of your yachting pride. We like to say, “Full Stainless – Beyond Good Looks.”

As with all ANDERSEN Winches™, our Full Stainless Self-Tailing winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Materials

Andersen winch drums are produced from grade 316L stainless steel, cold formed in stages during manufacture to further increase strength and hardness as it takes its final form. The resulting construction is lightweight, yet stiff and unyielding. 

Drive shafts are in grade 329 duplex stainless steel. Pawls are cut from a cold pressed profile in grade 316 stainless steel and are virtually unbreakable. 

The upper center stems are manufactured from aluminum bronze for ultimate durability. The combination of materials and design contribute to a lightweight, rigid final assembly that enhances. the mechanical efficiency of the winch. Andersen winces are of similar weight to winches with aluminum drums, but are far more durable. 

Power Rib™

ANDERSEN Winches© feature the Power Rib™. Unlike other winches with abrasive drum surfaces, ANDERSEN winch drums have vertical ribs running up the surface. This combined with the smooth polished stainless steel gives a maximum grip and minimum wear on ropes, reducing the replacements costs of sheets and halyards. What's more, the Power Rib principle simply makes sailing more pleasurable. Fewer turns on the winch make tacking easier. Sheets can be gently eased out without harsh snatching and the risks of overrides and jammed sheets are significantly reduced. The grip provided by the ribs will remain the same year after year, unlike many other winches with an abrasive or sandpaper-like surface. Such surfaces have a tendency to wear down both ropes and themselves.

Power Ratio

Power Ratio is the mechanical advantage of the winch and is calculated as follows:

length of handle x gear ratio

        radius of drum

The pull of the winch is based on the Power Ratio and not just on the physical size of the winch or the diameter of the drum. The Power Ratio is used to determine the load the winch may handle as follows:pull of handle (kg x Power Ratio = pull of winch (kg).

This means that by applying a load of 10kg, using a 10" standard handle, on a Power Ratio 40:1 winch, the winch can pull 400kg, assuming that the winch is 100% efficient. This is not possible in practice as the efficiency is reduced by internal mechanical friction losses.

Features

Anderson winch drums incorporate the distinctive Power Rib which ensures a controlled grip on the line at all times, whether trimming or easing. The highly polished stainless steel surface minimizes vertical friction and allows the loaded rope turns to slide easily upward as the drum rotates, without the shuddering and excessive rope wear seen on winches that rely on a rough surface finish for grip. 

Stainless steel roller bearings and ball bearings carry the highest drum loads to

Online
$1453.92 for Each
Mfr PN: RA2046010000
Stock: 2

ANDERSEN 46ST Compact Below Deck Electric FS Winch Variable Speed - 12V ANDERSEN 46ST Compact Below Deck Electric FS Winch Variable Speed - 12V
Online
$5815.80 for Each
Retail $6114.90
Mfr PN: RA2046014100
Stock: 0

46ST Compact Below Deck Electric Full Stainless Winch Variable Speed - 12V

Andersen Compact Motor™ electric winches allow you to hoist and trim sails at the push of a button regardless of physical strength, so any crew member can easily and safely trim sails and control lines.

Ease of installation
The Andersen Compact Motor™ electric winch is available in two formats for either Above Deck or Below Deck motor placement. Motor gearbox and controller are integrated into one compact unit with no extra control box necessary. Simplified electrical installation requires just the connection of positive and negative power cables to the motor terminals and the connection of the push button using the included output cable.

Efficient, variable speed
The Andersen Compact Motor™ is a brushless DC motor carefully matched to a low profile planetary gearbox which requires less space for installation, and draws considerably less current than traditional motor/gearbox configurations. Available in 12 volt and 24 volt models, Compact Motor™ electric winches operate at variable speed in proportion to the pressure applied to the push button, for smooth and quiet operation.

Illuminated "intelligent" push button
Compact Motor™ winches are supplied with a push button with integrated LED which illuminates when power to the winch system is on. The push button incorporates a hinged safety cover to prevent inadvertent winch operation and is water resistant rated to IP67. The push button also acts with the controller to flash status codes that assist with trouble shooting in the event of overload or where other system protection intervention occurs. A cable for connection of the push button is included for convenient installation.

Built-in protection
- Integrated overload protection - The controller is pre-set to stop the winch if the maximum pull load is exceeded. Operation can resume within a few seconds when the load returns below the limit.
- Thermal overload protection - The motor is fitted with a thermal cutout that disables the motor in case of overheating; it automatically resets after the temperature returns to normal.

As with all ANDERSEN Winches™, our Compact Motor™ Electric Winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes.

Specifications

  • Drum: 3-1/2 in. (89 mm)
  • Base: 7-1/16 in. (180 mm)
  • Height: 7-15/16 in. (202 mm)
  • Line Entry: 3-9/16 in. (90 mm)
  • Line Size: 5/16-9/16 in. (8-14 mm)
  • Weight: 46.3 lbs. (21 kg)
  • Max Deck Thickness: 2-7/16 in. (62 mm)
  • Motor Depth: 7-3/8 in. (188 mm)
  • Motor: 7-11/16 in. (195 mm)
Online
$5815.80 for Each
Retail $6114.90
Mfr PN: RA2046014100
Stock: 0

ANDERSEN 50 ST FS Self-Tailing Manual 2-Speed Winch - Full Stainless ANDERSEN 50 ST FS Self-Tailing Manual 2-Speed Winch - Full Stainless
Online
$1677.76 for Each
Mfr PN: RA2050010000
Stock: 2

50 ST FS Self-Tailing Manual 2-Speed Winch - Full Stainless

Power Rib™

ANDERSEN Winches feature the Power Rib™. Unlike other winches with abrasive drum surfaces, ANDERSEN winch drums have vertical ribs running up the surface. This combined with the smooth polished stainless steel gives a maximum grip and minimum wear on ropes, reducing the replacements costs of sheets and halyards. What’s more, the Power Rib principle simply makes sailing more pleasurable. Fewer turns on the winch make tacking easier. Sheets can be gently eased out without harsh snatching and the risks of overrides and jammed sheets are significantly reduced. The grip provided by the ribs will remain the same year after year, unlike many other winches with an abrasive or sandpaper-like surface. Such surfaces have a tendency to wear down both ropes and themselves.

Power Ratio

Power Ratio is the mechanical advantage of the winch and is calculated as follows:

length of handle x gear ratio 
          radius of drum

The pull of the winch is based on the Power Ratio and not just on the physical size of the winch or the diameter of the drum. The Power Ratio is used to determine the load the winch may handle as follows: pull of handle (kg x Power Ratio = pull of winch (kg).

This means that by applying a load of 10kg, using a 10" standard handle, on a Power Ratio 40:1 winch, the winch can pull 400kg, assuming that the winch is 100% efficient. This is not possible in practice as the efficiency is reduced by internal mechanical friction losses.

Specifications:

  • Drum Ø D: 3-1/2"
  • Base Ø B: 7-1/16"
  • Height H: 7-15/16"
  • Line Entry L: 3-9/16"
  • Line Size: 5/16-9/16"
  • Weight: 17.2lb
  • Gear ratio 1st speed: 2.8 : 1
  • Gear ratio 2nd speed: 8.8 : 1
  • Power ratio 1st speed: 15.7 :1
  • Power ratio 2nd speed: 49.3 : 1
Online
$1677.76 for Each
Mfr PN: RA2050010000
Stock: 2

ANDERSEN 50ST Compact Below Deck Electric FS Winch Variable Speed - 12V ANDERSEN 50ST Compact Below Deck Electric FS Winch Variable Speed - 12V
Online
$5812.48 for Each
Retail $6522.90
Mfr PN: RA2050014100
Stock: 2

50ST Compact Below Deck Electric Full Stainless Winch Variable Speed - 12V

Andersen Compact Motor™ electric winches allow you to hoist and trim sails at the push of a button regardless of physical strength, so any crew member can easily and safely trim sails and control lines.

Ease of installation
The Andersen Compact Motor™ electric winch is available in two formats for either Above Deck or Below Deck motor placement. Motor gearbox and controller are integrated into one compact unit with no extra control box necessary. Simplified electrical installation requires just the connection of positive and negative power cables to the motor terminals and the connection of the push button using the included output cable.

Efficient, variable speed
The Andersen Compact Motor™ is a brushless DC motor carefully matched to a low profile planetary gearbox which requires less space for installation, and draws considerably less current than traditional motor/gearbox configurations. Available in 12 volt and 24 volt models, Compact Motor™ electric winches operate at variable speed in proportion to the pressure applied to the push button, for smooth and quiet operation.

Illuminated "intelligent" push button
Compact Motor™ winches are supplied with a push button with integrated LED which illuminates when power to the winch system is on. The push button incorporates a hinged safety cover to prevent inadvertent winch operation and is water resistant rated to IP67. The push button also acts with the controller to flash status codes that assist with trouble shooting in the event of overload or where other system protection intervention occurs. A cable for connection of the push button is included for convenient installation.

Built-in protection
- Integrated overload protection - The controller is pre-set to stop the winch if the maximum pull load is exceeded. Operation can resume within a few seconds when the load returns below the limit.
- Thermal overload protection - The motor is fitted with a thermal cutout that disables the motor in case of overheating; it automatically resets after the temperature returns to normal.

As with all ANDERSEN Winches™, our Compact Motor™ Electric Winch features the exclusive stainless steel Power Rib™ drum for maximum power and extended line life. This model also uses our exclusive self-tailing device that automatically accommodates a wide range of different line sizes. 

Specifications

  • Drum: 3-1/2 in. (89 mm)
  • Base: 7-1/16 in. (180 mm)
  • Height: 7-15/16 in. (202 mm)
  • Line Entry: 3-9/16 in. (90 mm)
  • Line Size: 5/16-9/16 in. (8-14 mm)
  • Weight: 46.3 lbs. (21 kg)
  • Max Deck Thickness: 2-7/16 in. (62 mm)
  • Motor Depth: 7-3/8 in. (188 mm)
  • Motor: 7-11/16 in. (195 mm)
Online
$5812.48 for Each
Retail $6522.90
Mfr PN: RA2050014100
Stock: 2

ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/28ST Winch ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/28ST Winch
Online
$3937.48 for Each
Retail $4482.90
Mfr PN: RA2028214100
Stock: 1

Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V for 28ST Winch

The uncompromising ANDERSEN Variable-speed Compact Motor™ is especially developed for use as a winch motor. It is available in two versions; Below Deck, with smaller, built-in dimensions than a standard motor and Above Deck, featuring the winch mounted directly on the motor for deck or mast installation. This motor is highly efficient, with an impressive line speed and first-rate maximum load. The unit is extremely easy to install and demonstrates why ANDERSEN Products are in a class of their own.

The motor is built on an entirely new commutator principle using no carbon brushes, resulting in the virtual elimination of wear and tear. This new approach to motors also provides other advantages; including 30-50% less power consumption compared to a conventional electric motor.

Electric conversion kits are delivered mounted to a stainless steel winch/deck connection plate and have everything you need for do-it-yourself mounting including installation manual, switches and cable terminals.

Important Information
Mounting of an Above Deck Compact Motor™ winch on a vertical surface is not recommended, as it increases exposure to potential problems of excessive moisture and water ingress which could lead to damage not covered by warranty. The motor/gearbox unit of any Above Deck Compact Motor™ Electric Winch is more exposed to the elements than a below deck installation which keeps the motor unit and gearbox more protected. It is important to take reasonable precautions to protect the unit from unnecessary exposure, and carry out regular seasonal maintenance including the lubrication of the motor shaft seal. This is just good seamanship. On commercial and military vessels, it is common to see exposed equipment with electric motors and gearboxes fitted with covers when not in use or to protect them from heavy spray, etc. Equipment on yachts deserves the same proper care.

** Before ordering, please contact us to ensure your Andersen Winch is compatible with this Conversion Kit. Refer to the Winch Product Version Number when inquiring or ordering powered Conversion Kits. The production year, month and version no. [YY-MM-VER.] are stamped on the top side of the deck flange, between the mounting bolt holes. You’ll find it, when the polished winch drum is removed. **

Online
$3937.48 for Each
Retail $4482.90
Mfr PN: RA2028214100
Stock: 1

ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/34ST Winch ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/34ST Winch
Online
$3937.48 for Each
Retail $4482.90
Mfr PN: RA2034214100
Stock: 2

Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V for 34ST Winch

The uncompromising ANDERSEN Variable-speed Compact Motor™ is especially developed for use as a winch motor. It is available in two versions; Below Deck, with smaller, built-in dimensions than a standard motor and Above Deck, featuring the winch mounted directly on the motor for deck or mast installation. This motor is highly efficient, with an impressive line speed and first-rate maximum load. The unit is extremely easy to install and demonstrates why ANDERSEN Products are in a class of their own.

The motor is built on an entirely new commutator principle using no carbon brushes, resulting in the virtual elimination of wear and tear. This new approach to motors also provides other advantages; including 30-50% less power consumption compared to a conventional electric motor.

Electric conversion kits are delivered mounted to a stainless steel winch/deck connection plate and have everything you need for do-it-yourself mounting including installation manual, switches and cable terminals.

Important Information
Mounting of an Above Deck Compact Motor™ winch on a vertical surface is not recommended, as it increases exposure to potential problems of excessive moisture and water ingress which could lead to damage not covered by warranty. The motor/gearbox unit of any Above Deck Compact Motor™ Electric Winch is more exposed to the elements than a below deck installation which keeps the motor unit and gearbox more protected. It is important to take reasonable precautions to protect the unit from unnecessary exposure, and carry out regular seasonal maintenance including the lubrication of the motor shaft seal. This is just good seamanship. On commercial and military vessels, it is common to see exposed equipment with electric motors and gearboxes fitted with covers when not in use or to protect them from heavy spray, etc. Equipment on yachts deserves the same proper care.

** Before ordering, please contact us to ensure your Andersen Winch is compatible with this Conversion Kit. Refer to the Winch Product Version Number when inquiring or ordering powered Conversion Kits. The production year, month and version no. [YY-MM-VER.] are stamped on the top side of the deck flange, between the mounting bolt holes. You’ll find it, when the polished winch drum is removed. **

Online
$3937.48 for Each
Retail $4482.90
Mfr PN: RA2034214100
Stock: 2

ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/40ST Winch ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/40ST Winch
Online
$3937.48 for Each
Retail $4482.90
Mfr PN: RA2040214100
Stock: 2

Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V for 40ST Winch

The uncompromising ANDERSEN Variable-speed Compact Motor™ is especially developed for use as a winch motor. It is available in two versions; Below Deck, with smaller, built-in dimensions than a standard motor and Above Deck, featuring the winch mounted directly on the motor for deck or mast installation. This motor is highly efficient, with an impressive line speed and first-rate maximum load. The unit is extremely easy to install and demonstrates why ANDERSEN Products are in a class of their own.

The motor is built on an entirely new commutator principle using no carbon brushes, resulting in the virtual elimination of wear and tear. This new approach to motors also provides other advantages; including 30-50% less power consumption compared to a conventional electric motor.

Electric conversion kits are delivered mounted to a stainless steel winch/deck connection plate and have everything you need for do-it-yourself mounting including installation manual, switches and cable terminals.

Important Information
Mounting of an Above Deck Compact Motor™ winch on a vertical surface is not recommended, as it increases exposure to potential problems of excessive moisture and water ingress which could lead to damage not covered by warranty. The motor/gearbox unit of any Above Deck Compact Motor™ Electric Winch is more exposed to the elements than a below deck installation which keeps the motor unit and gearbox more protected. It is important to take reasonable precautions to protect the unit from unnecessary exposure, and carry out regular seasonal maintenance including the lubrication of the motor shaft seal. This is just good seamanship. On commercial and military vessels, it is common to see exposed equipment with electric motors and gearboxes fitted with covers when not in use or to protect them from heavy spray, etc. Equipment on yachts deserves the same proper care.

** Before ordering, please contact us to ensure your Andersen Winch is compatible with this Conversion Kit. Refer to the Winch Product Version Number when inquiring or ordering powered Conversion Kits. The production year, month and version no. [YY-MM-VER.] are stamped on the top side of the deck flange, between the mounting bolt holes. You’ll find it, when the polished winch drum is removed. **

Online
$3937.48 for Each
Retail $4482.90
Mfr PN: RA2040214100
Stock: 2

ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/46ST Winch ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/46ST Winch
Online
$4845.68 for Each
Retail $5094.90
Mfr PN: RA2046214100
Stock: 0

Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V for 46ST Winch

The uncompromising ANDERSEN Variable-speed Compact Motor™ is especially developed for use as a winch motor. It is available in two versions; Below Deck, with smaller, built-in dimensions than a standard motor and Above Deck, featuring the winch mounted directly on the motor for deck or mast installation. This motor is highly efficient, with an impressive line speed and first-rate maximum load. The unit is extremely easy to install and demonstrates why ANDERSEN Products are in a class of their own.

The motor is built on an entirely new commutator principle using no carbon brushes, resulting in the virtual elimination of wear and tear. This new approach to motors also provides other advantages; including 30-50% less power consumption compared to a conventional electric motor.

Electric conversion kits are delivered mounted to a stainless steel winch/deck connection plate and have everything you need for do-it-yourself mounting including installation manual, switches and cable terminals.

Important Information
Mounting of an Above Deck Compact Motor™ winch on a vertical surface is not recommended, as it increases exposure to potential problems of excessive moisture and water ingress which could lead to damage not covered by warranty. The motor/gearbox unit of any Above Deck Compact Motor™ Electric Winch is more exposed to the elements than a below deck installation which keeps the motor unit and gearbox more protected. It is important to take reasonable precautions to protect the unit from unnecessary exposure, and carry out regular seasonal maintenance including the lubrication of the motor shaft seal. This is just good seamanship. On commercial and military vessels, it is common to see exposed equipment with electric motors and gearboxes fitted with covers when not in use or to protect them from heavy spray, etc. Equipment on yachts deserves the same proper care.

** Before ordering, please contact us to ensure your Andersen Winch is compatible with this Conversion Kit. Refer to the Winch Product Version Number when inquiring or ordering powered Conversion Kits. The production year, month and version no. [YY-MM-VER.] are stamped on the top side of the deck flange, between the mounting bolt holes. You’ll find it, when the polished winch drum is removed. **

Online
$4845.68 for Each
Retail $5094.90
Mfr PN: RA2046214100
Stock: 0

ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/50ST Winch ANDERSEN Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V f/50ST Winch
Online
$4562.48 for Each
Retail $5094.90
Mfr PN: RA2050214100
Stock: 2

Below Deck Variable Speed Compact Motor Electric Conversion Kit - 12V for 50ST Winch

The uncompromising ANDERSEN Variable-speed Compact Motor™ is especially developed for use as a winch motor. It is available in two versions; Below Deck, with smaller, built-in dimensions than a standard motor and Above Deck, featuring the winch mounted directly on the motor for deck or mast installation. This motor is highly efficient, with an impressive line speed and first-rate maximum load. The unit is extremely easy to install and demonstrates why ANDERSEN Products are in a class of their own.

The motor is built on an entirely new commutator principle using no carbon brushes, resulting in the virtual elimination of wear and tear. This new approach to motors also provides other advantages; including 30-50% less power consumption compared to a conventional electric motor.

Electric conversion kits are delivered mounted to a stainless steel winch/deck connection plate and have everything you need for do-it-yourself mounting including installation manual, switches and cable terminals.

Important Information
Mounting of an Above Deck Compact Motor™ winch on a vertical surface is not recommended, as it increases exposure to potential problems of excessive moisture and water ingress which could lead to damage not covered by warranty. The motor/gearbox unit of any Above Deck Compact Motor™ Electric Winch is more exposed to the elements than a below deck installation which keeps the motor unit and gearbox more protected. It is important to take reasonable precautions to protect the unit from unnecessary exposure, and carry out regular seasonal maintenance including the lubrication of the motor shaft seal. This is just good seamanship. On commercial and military vessels, it is common to see exposed equipment with electric motors and gearboxes fitted with covers when not in use or to protect them from heavy spray, etc. Equipment on yachts deserves the same proper care.

** Before ordering, please contact us to ensure your Andersen Winch is compatible with this Conversion Kit. Refer to the Winch Product Version Number when inquiring or ordering powered Conversion Kits. The production year, month and version no. [YY-MM-VER.] are stamped on the top side of the deck flange, between the mounting bolt holes. You’ll find it, when the polished winch drum is removed. **

Online
$4562.48 for Each
Retail $5094.90
Mfr PN: RA2050214100
Stock: 2

Attwood 20 Liter Dry Bag Attwood 20 Liter Dry Bag
Online
$22.66 for Each
Retail $27.99
Mfr PN: 11897-2
Stock: 0
Dry Bag - 20 Liter

Attwood's Dry Bag is produced with heavy duty materials to provide strong, durable, waterproof storage for your items both on the water and land. 20 liter (5.28 gallon) storage capacity. Safety yellow coloring for easy visibility on the water. Multiple D-rings allow waterproof cases, dry boxes, and other essentials to attach conveniently. Soft touch integrated carry handle for ease in handling.

  • Waterproof construction
  • Made out of heavy duty 500 denier PVC coated mesh fabric
  • Integrated carry handle
  • 1-1/2" adjustable shoulder strap

WarningWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Online
$22.66 for Each
Retail $27.99
Mfr PN: 11897-2
Stock: 0

Attwood Cowl Ventilator Attwood Cowl Ventilator
Online
$22.66 for Each
Retail $29.99
Mfr PN: 1364A3
Stock: 34

Cowl Ventilator

Attwood hull-mounted vents are designed to install by fastening as a complete unit from either inside or outside the hull. Ventilation hose (not included) twists into the bottom of the box to form a raised water barrier. Plastic vents are corrosion-resistant, will not discolor. All collector boxes and vents are designed for intake or exhaust and meet ABYC H-2 cross sectional area requirements.

For use with 3" I.D. wire-supported ventilation hose. Features flexible hose flange that is screwed onto hose, then vent snaps onto the flange. Vent constructed of chrome-plated die-cast Perma-Plate® ZAMAK. Flange is non-corrosive plastic. Installs with #8 screws.

Installation Hole Size: 3-1/4" to 3-1/2"

WarningWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Online
$22.66 for Each
Retail $29.99
Mfr PN: 1364A3
Stock: 34

Attwood Flush Hatch Pull Attwood Flush Hatch Pull
Online
$4.63 for Each
Retail $5.99
Mfr PN: 2027-7
Stock: 0

Flush Hatch Pull

The new low profile flush hatch pull is an easy access handle for installation in lids, doors, compartments, and hatches. Handle is easy to grip, even with gloved hands. Durable ABS construction with black textured finish.

Online
$4.63 for Each
Retail $5.99
Mfr PN: 2027-7
Stock: 0

Attwood Utility Snap Hook - 4" Attwood Utility Snap Hook - 4"
Online
$7.31 for Each
Retail $9.99
Mfr PN: 7653L3
Stock: 4

Utility Snap Hook - 4"

This Attwood Utility Snap Hook is a versatile and dependable resource for connecting items or establishing a tie-down point. This sturdy zinc-plated steel hook has a spring-loaded closure that makes it easy to attach this hook to an item and remove the hook just as quickly and easily. This light-duty hook is 4 inches long, has a ¼-inch ring diameter, and is rated for a 500-pound safe load. 

Features:

  • Versatile and dependable resource for connecting items or establishing a tie-down point
  • Sturdy zinc-plated steel hook
  • Spring-loaded closure attaches hook to an item quickly and easily
  • Light-duty hook
  • Rated for a 500-pound safe load
  • 4 inches long
Online
$7.31 for Each
Retail $9.99
Mfr PN: 7653L3
Stock: 4

Barton Marine Aluminum Winch Handle - 8" Barton Marine Aluminum Winch Handle - 8"
Online
$39.40 for Each
Retail $66.20
Mfr PN: 21 001
Stock: 0
Aluminum Winch Handle - 8"

All designed to fit international star sockets and standard deck filler caps.

Light duty, inexpensive handles w/easy-grip roller handle and 'Spectro' grey anodised finish.

Important note:
These handles should not be used on large, two-speed winches as they are not designed for high loads in an anti-clockwise direction. SWL 40kg (88.18lbs)
Online
$39.40 for Each
Retail $66.20
Mfr PN: 21 001
Stock: 0

Barton Marine Extra Large Wincher (Pair) Barton Marine Extra Large Wincher (Pair)
Online
$93.94 for Each
Retail $101.46
Mfr PN: 21 644
Stock: 4
The Barton 'Wincher'
(Pair)

Max Drum Ø 90-100mm (3.54"-3.94")
Max Rope Ø 12-16mm (0.47"-0.63")
Weight 387g (13.65oz)

A specially designed rubber moulding which fits over the top of standard winches, converting them to self-tailing.

This simple operation works when the line is sheeted under load, which means the coils climb up the winch drum and then become gripped by the underside of the Wincher's rubber body.

Cleating is achieved by locking the sheet into the Wincher's ribbed central groove.

Barton 'Winchers' are easy to fit and available in four sizes to suit a wide range of popular winches.
Online
$93.94 for Each
Retail $101.46
Mfr PN: 21 644
Stock: 4

Barton Marine Floating Locking Winch Handle - 8" Barton Marine Floating Locking Winch Handle - 8"
Online
$80.37 for Each
Retail $106.58
Mfr PN: 21 034
Stock: 0
Floating Handle - 8" Locking

Featuring a moulded body with an integral moulded handle shaft.
Locking mechanism is with a positive, easy action thumb switch. Handle floats in salt and freshwater.

Important note:
Floating winch handles have a SWL of 40kg (88.18lbs) and are intended for lightweight use only.
Online
$80.37 for Each
Retail $106.58
Mfr PN: 21 034
Stock: 0

Barton Marine Furling Drum - 76mm Barton Marine Furling Drum - 76mm
Online
$83.17 for Each
Retail $122.44
Mfr PN: 42 334
Stock: 3
Furling Drum - 76mm
Holds up to 4.3M of Line

Drums are moulded from glass fibre reinforced nylon with stainless steel swivel and ball bearing assemblies. Furling drums will accept line up to 4mm diameter.

  • Drum Diameter:76mm
  • Sail Area:60 square foot
  • Break Load:1,108kg
  • Safe Working Load:554kg
  • Weight:218g
Online
$83.17 for Each
Retail $122.44
Mfr PN: 42 334
Stock: 3

Barton Marine Furling Drum - 95mm Barton Marine Furling Drum - 95mm
Online
$92.34 for Each
Retail $152.84
Mfr PN: 42 335
Stock: 4
Furling Drum - 95mm
Holds up to 8.5M of Line

Drums are moulded from glass fibre reinforced nylon with stainless steel swivel and ball bearing assemblies. Furling drums will accept line up to 4mm diameter.

  • Drum Diameter:95mm
  • Sail Area:100 square foot
  • Break Load:1,108kg
  • Safe Working Load:554kg
  • Weight:281g
Online
$92.34 for Each
Retail $152.84
Mfr PN: 42 335
Stock: 4

Barton Marine Genoa Car Fits 20mm (¾") 'T' Track Barton Marine Genoa Car Fits 20mm (¾") 'T' Track
Online
$63.74 for Each
Retail $86.04
Mfr PN: 22 100
Stock: 3
Plain Bearing Genoa Cars w/Plunger Stops

Genoa Cars w/Plunger Stops
Features a precision turned Ertalyte sheave, through-bolted for extra strength. The positive action plunger mechanism has an easy-grip knob

A popular range of genoa cars and sliders designed to run on 20mm (3/4") 'T' track. All are manufactured from high quality marine grade aluminium with our unique 'Spectro' grey anodised finish for added protection.

This useful range will find a wide variety of applications on larger dinghies, dayboats and light cruiser/racers.

  • 'Spectro' grey anodised finish
  • Stainless steel plunger stops with positive action
  • Moulded nylon slide inserts ensure free running
  • Large, easy-grip plunger knobs
  • Heavy-duty genoa car options


Cars and sliders are compatible with all makes of 'T' track.
Modified slider inserts available for obscure sizes.

20mm 'T' Section Track
Drilled for fastenings and plunger stops. 'Spectro' grey anodised and supplied in metric lengths.

Specifications and Dimensions:
Length: 60mm (2.4")
Width: 34mm (1.34")
Height: 65mm (2.56")
Sheave Ø: 30mm (1.18")
Max Rope Ø; 10mm (0.4")
Break Load: 1160kg (2,557.4lbs)
SWL: 580kg (1,278.7lbs)
Weight: 119g (0.26lbs)
Online
$63.74 for Each
Retail $86.04
Mfr PN: 22 100
Stock: 3

Barton Marine Genoa Car Fits 25mm (1") 'T' Track Barton Marine Genoa Car Fits 25mm (1") 'T' Track
Online
$99.08 for Each
Retail $133.74
Mfr PN: 25 100
Stock: 6
Plain Bearing Genoa Cars w/Plunger Stops

Genoa Cars w/Plunger Stops
Features a precision turned Ertalyte sheave, through-bolted for extra strength. The positive action plunger mechanism has an easy-grip knob

A popular range of genoa cars and sliders designed to run on 25mm (1") 'T' track. All are manufactured from high quality marine grade aluminium with our unique 'Spectro' grey anodised finish for added protection.

This useful range will find a wide variety of applications on larger dinghies, dayboats and light cruiser/racers.

  • 'Spectro' grey anodised finish
  • Stainless steel plunger stops with positive action
  • Moulded nylon slide inserts ensure free running
  • Large, easy-grip plunger knobs
  • Heavy-duty genoa car options


Cars and sliders are compatible with all makes of 'T' track.
Modified slider inserts available for obscure sizes.

25mm 'T' Section Track
Drilled for fastenings and plunger stops. 'Spectro' grey anodised and supplied in metric lengths.

Specifications and Dimensions:
Length: 80mm (3.15")
Width: 42mm (1.65")
Height: 87mm (3.43")
Sheave Ø: 40mm (1.57")
Max Rope Ø; 2 x 12mm (2 x 0.47")
Break Load: 2,280kg (5,026.54lbs)
SWL: 1,140kg (2,513.3lbs)
Weight: 247g (0.54lbs)
Online
$99.08 for Each
Retail $133.74
Mfr PN: 25 100
Stock: 6

Barton Marine Genoa Car fits 32mm (1-1/4") 'T' Track Barton Marine Genoa Car fits 32mm (1-1/4") 'T' Track
Online
$136.48 for Each
Retail $208.66
Mfr PN: 32 100
Stock: 6
Plain Bearing Genoa Cars w/Plunger Stops

Genoa Cars w/Plunger Stops
Feature precision turned Ertalyte sheaves running on a large diameter centre bearing, for friction-free performance under load. Sheaves are designed with extra width to accept two sheets. The sheave axle is through-bolted and riveted for extra strength.

A popular range of genoa cars and sliders designed to run on 32mm (1-1/4") 'T' track. All are manufactured from high quality marine grade aluminium with our unique 'Spectro' grey anodised finish for added protection.

Moulded nylon inserts to ensure free, smooth running under load and prevent damage to finish or potential corrosion.

  • 'Spectro' grey anodised finish
  • Stainless steel plunger stops with positive action
  • Moulded nylon slide inserts ensure free running
  • Large, easy-grip plunger knobs
  • Heavy-duty genoa car options


Cars and sliders are compatible with all makes of 'T' track.
Modified slider inserts available for obscure sizes.

32mm 'T' Section Track
Drilled for fastenings and plunger stops. 'Spectro' grey anodised and supplied in metric lengths.

Specifications and Dimensions:
Length: 109mm (4.3")
Width: 52mm (2.05")
Height: 102mm (4.02")
Sheave Ø: 50mm (1.97)
Max Rope Ø; 2 x16mm (2 x 0.63")
Break Load: 3,280kg (7,231.7lbs)
SWL: 1,640kg (3,615.6lbs)
Weight: 469g (1.03lbs)
Online
$136.48 for Each
Retail $208.66
Mfr PN: 32 100
Stock: 6

Barton Marine Large Wincher (Pair) Barton Marine Large Wincher (Pair)
Online
$91.44 for Each
Mfr PN: 21 643
Stock: 8
The Barton 'Wincher'
(Pair)

Max Drum Ø 80-90mm (3.15"-3.54")
Max Rope Ø 12-14mm (0.47"-0.55")
Weight 278g (9.81oz)

A specially designed rubber moulding which fits over the top of standard winches, converting them to self-tailing.

This simple operation works when the line is sheeted under load, which means the coils climb up the winch drum and then become gripped by the underside of the Wincher's rubber body.

Cleating is achieved by locking the sheet into the Wincher's ribbed central groove.

Barton 'Winchers' are easy to fit and available in four sizes to suit a wide range of popular winches.
Online
$91.44 for Each
Mfr PN: 21 643
Stock: 8